Life Fitness Atmos Treadmill Parts & Diagram
Life Fitness · Treadmill · Model MRT-CGCHV-01
A compact, commercial-grade treadmill built for tight hotel and apartment fitness rooms. It delivers the dependable running and walking experience guests expect from Life Fitness, with a right-sized footprint and simplified service access for low downtime.
Diagram pages
- Base Frame Electronics
- Bridge
- Communication Port
- Console Weldment
- Drive System
- Emergency Stop
- End Caps, Levelers and Rear Roller
- Frame, Deck, and Belt
- Front Roller
- Lift Frame and Wheels
- Power Cord Retainer Bracket and IEC Receptacle
- Shroud, Bridge, Lower
- Shroud, Bridge, Upper
- Shroud, Console, Lower and Back
- Shroud, Motor Cover, Front
- Shroud, Motor Cover, Top
- Stop Strips and Lower Extrusions
- Uprights
- Wiring Diagram, Base
- Wiring Diagram, Console
Parts in this machine
All 121 parts in this machine. Start a free PlateLog trial to see real part numbers and ordering links.
- AC Line Filter, 10A
- AC Line Filter
- Torx Pan Head Self-Tapping Screw
- MDB PC Board Assembly
- Rear Power Input Cover
- Plastic Locking Wire Clip
- 24VDC Power Supply
- Line Filter to Power Supply Cable
- Cable Tie (3-7/8 inch)
- Momentary Action Switch
- Switch Retaining Clip
- Bridge Weldment
- M8 Threaded Insert
- M8 Hex Washer Screw
- Coax Plug
- RJ45 Receptacle
- On/Off Switch
- Coaxial Panel Mount Connector
- Coaxial Cable (RG6, 120 inch)
- Shielded RJ45 Coupler
- CAT5E Cable (96 inch)
- Console Legacy Weldment
- M5 Pan Head Screw
- AC Motor Assembly (4HP)
- AC Motor (4HP)
- Poly-V Pulley (1.616 inch)
- Setscrews
- Cast Iron Flywheel with Fan
- M10 Flange Screw
- M8 Hex Bolt (60mm)
- Insulating Pad
- Insulating Washer
- Locking Nut (M8 x 1.25)
- Washers
- Drive Belt
- Tether Assembly
- Tether Plate
- Reed Switch Bracket
- Pan Head Screw (6-19 x 6)
- Screw (Roller Guard)
- Left Tread End Cap
- Rear Tensioning Bolt
- Left Rear Roller Guard
- Plastic Grommet
- Flat Washer
- Rear Roller
- Right Rear Roller Guard
- Right Tread End Cap
- Leveler Tube Cap
- Leg Leveler
- U-Clip Nut (1/4-20)
- Tecspak Washer
- Tecspak Screw
- Tecspak Cushion Block
- Walking Deck (20x60)
- Flat Head Screw (1/4-20)
- Walking Belt (22x60)
- Extrusion Mounting Brackets
- Torx Pan Screws
- Extrusion Mounting Clip
- Front Roller Assembly with Pulley
- Tensioning Bolt
- Pulley Guard
- Lift Frame Weldment
- Lift Frame Wheels
- Push Nut
- Clevis Pin (3/8 x 20)
- Cotter Pin
- Lift Frame End Caps
- Actuator Lift Frame Pin
- E-Ring (1/2 inch)
- Rubber Bumper
- Linear Actuator (115V)
- Linear Actuator (230V)
- Hex Head Bolt (3/8-16 x 1.75)
- Nylock Nut 3/8-16
- Pan Head Screw (M4 x 10mm)
- IEC Receptacle
- Power Cord Retainer Bracket
- Flange Bushing
- Lower Bridge Shroud Assembly
- M9.55 x 16.5 Spring Fastener Clip
- Truss Head Tapping Screw (8-18 x 1/2)
- Upper Bridge Shroud Assembly
- Onsert (.312 O.D. B)
- STOP Keypad
- Lower Console Shroud Assembly
- Back Console Shroud Assembly
- Life Fitness Script Logo (5.25 inch)
- Front Motor Cover Shroud
- Pan Head Screw (M4.2 x 19)
- Square Grommet
- Top Motor Cover Shroud
- Lower Left Extrusion
- Life Fitness Script Logo (7.5 inch)
- Lower Right Extrusion
- Left Top Step Extrusion
- Right Top Step Extrusion
- Felt Bumper
- Right Upright Weldment
- Left Upright Weldment
- Upright End Cap
- Tube End Cap
- Console to Base Power Cable
- Console to Base Signal Cable
- Ferrite Suppression Core-Case
- Ferrite Bead
- Ferrite Bead Suppressor
- Power Input Cable
- Ground Cable
- Black Switch to Filter Cable
- White Switch to Filter Cable
- MOV Filter Cable
- Hi-Pot Jumper Cable
- White Power Input Cable
- Black Power Input Cable
- Male Tab Cap
- Home Switch Cable
- Motor Jumper Cable
- Console Ground Cable
- Tread Bridge Interface Cable
Start a free 14-day trial to unlock the interactive diagrams with real part numbers.
